The EIA ceased operations on February 11, 2011, but the former sectors continue to serve the constituencies of EIA. EIA designated ECA to continue to develop standards for interconnect, passive and electro-mechanical (IP&E) electronic components under the ANSI-designation of EIA standards. All other electronic components standards are managed by their respective sectors. ECA is expected to merge with the National Electronic Distributors Association (NEDA) to form the Electronic Components Industry Association (ECIA). However, the EIA standards brand will continue for IP&E standards within ECIA. As currently authorized, any ANSI standard designated at ANSI EIA-xxx is developed and/or managed by ECA (and, in the future, ECIA).
EIA/TIA/IS-55 Recommended Minimum Performance Standards of 800 MHz Dual Mode Mobile Stations
EIA/TIA/IS-66 Sectional Specification for Nonpressurized Fiber Optic Splice Closures
EIA-96
TIA/EIA-136-310-A-1 TDMA Third Generation Wireless - Radio Link Protocol –1
JEP-143C Solid-State Reliability Assessment and Qualification Methodologies
EIA-170/RS-170 Electrical Performance Standards-Monochrome Television Studio Facilities 01 November 1957.
Note: EIA-170 only appears on the cover page of the document, internal pages are labeled RS-170 in the upper right corner.
EIA-170/RS-170 applies only to monochrome (black & white) video.
The later color video version is RS-170A which shows color burst and the 4 color field sequence of NTSC.
The RS-170A version is only a tentative standard, and was never formally adopted. NAB Engineering Handbook Seventh Edition.[1]
EIA-222 Standards for antenna mast structural integrity
RS-225, 50Ω RF high power RF connectors, (EIA RF Connectors)
RS-232 (or EIA-232) electrical characteristics, single-ended voltage digital interface circuit (serial data communications)
RS-259, 75Ω RF high power RF connectors, (EIA RF Connectors)
EIA-274 is the most common
NC code format. In the machine tool industry it also known as
G-code. In the
PCB industry
Standard Gerber, now revoked, was based on it.
EIA/TIA-455-A Standard Test Procedure for Fiber Optic Fibers, Cables, Transducers, Sensors, Connecting and Terminating Devices, and Other Fiber Optic Components
EIA/TIA-455-12A FOTP-12 Fluid Immersion Test for Fiber Optic Components
EIA/TIA-455-37A FOTP-37 Low or High Temperature Bend Test for Fiber Optic Cable
EIA/TIA-455-48B FOTP-48 Measurement of Optical Fiber Cladding Diameter Using Laser-Based Instruments
EIA/TIA-455-87B FOTP-87 Fiber Optic Cable Knot Test
EIA/TIA-455-188 FOTP-188 Low Temperature Testing of Fiber Optic Components
EIA-RS-481 Taping/Leadless Components for Automatic Placement
RS-485 Electrical Characteristics of Generators and Receivers for Use in Balanced Digital Multipoint Systems (serial data communications)
CEA-709.1-B Control Network Protocol Specification
800–899
EIA/CEA-861 A DTV Profile for Uncompressed High Speed Digital Interfaces (now
CTA-861)
TIA/EIA/IS-880 TIA-41-D Based Network Enhancements for CDMA Packet Data Service (C-PDS) Phase 1
900–999
TIA-968-A Technical Requirements for Connection of Terminal Equipment to the Telephone Network
1000–1099
TIA-1096-A Connector Requirements for Connection of Terminal Equipment to the Telephone Network
2000–2099
TIA/EIA/IS-2000.5-A Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread Spectrum Systems
TIA/EIA/IS-2000.5-C Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread Spectrum Systems
3100–3199
EIA SP 3128 POLARIZING/CODING KEY OVERSTRESS TEST PROCEDURE FOR ELECTRICAL CONNECTORS
Notes
The above list of standards is not only incomplete, but also out of date. For example, the standard on capacitor dielectric classes is as of Nov 2002: EIA-198-1-F Ceramic Dielectric Capacitors: Classes I, II, III, and IV
RS is for "
Recommended Standard", an early prefix used for electronic standards