From Wikipedia, the free encyclopedia
This picture depicts the correct depths of a face cut and back cut as well as the correct percentage of holding or "hinge" wood that should be left on the stump while hand-felling. Figure 1. depicts the face cut, figure 2. depicts the hinge wood, and figure 3. depicts the back cut.

Hand felling is the process of cutting down trees using a tool operated with the hands, such as an axe, saw or chainsaw.

Techniques

Most trees that are felled by hand are done so in the same general way. Utilizing proper felling techniques is important not only for operator safety but also for forestry and logging applications related to timber value and potential timber value loss. [1] Maintaining proper posture while felling is also important, i.e., kneeling or squatting instead of stooping or bending over with straight legs. [2] [3] The use of improper felling techniques is dangerous, but may also reduce productivity and log supply, leading to increases in production costs in forestry and logging felling applications. [4]

A good rule of thumb for all felling scenarios is to make the depth of the face cut or undercut, which is your directional angles notch face the way you want the tree to fall, roughly equal to 1/3 the diameter of the tree. [5] Additionally, one should leave about 10% for your holding wood or hinge wood to direct the tree on its way to the ground. [6] The remaining 2/3 of the tree is for the back cut, which acts as the final piece of the puzzle to get the tree on the ground.

There are three types of directional felling notches that are most commonly used in the logging and arboriculture industries by chainsaw operators. They are the conventional, the Humbolt, and the open-face. [5] Each has different advantages and disadvantages based on the type of tree, the condition of the tree, the environment surrounding the tree, and the region in which the tree is being felled. [6]

Face-Cuts

A Conventional face cut in a Norway Maple.

The conventional face cut is perhaps the most commonly used and most well recognized face cut used in the world today. It has an open upwards angle of plus or minus 35 degrees, and is the easiest undercut to learn. Lining up the cuts is fairly easy and quick, and it gives the operator the most directional control of the tree as it falls since the top of the tree will always hit the ground first due to the prolonged time the tree spends on the stump. [5] Some downsides of the conventional face cut are that the two flat faces of the angle can come into contact prior to the tree actually hitting the ground, which can cause stump pull, log fiber pull, or a barber chair effect where the tree splits in half and snaps back in the direction of the operator. [5] All of the above scenarios are extremely dangerous and negatively effect the monetary value quality of the tree in a lumber production scenario.

A Humbolt face cut in a Norway maple.

The Humbolt face cut is a less well-known felling undercut, and is commonly used in the pacific northwest and pacific coast of Canada and Alaska. [5] A Humbolt face cut has a downward 45 degree angle, and allows the directional face cut to be made out of the stump rather than the log. Additionally, the downward open angle of the Humbolt allows the tree to jump off of the stump when it falls, making the tree always land butt first and lay out, which is not only safer for the operator but also smashes up less wood in a timber production scenario. [6] Some downsides of the Humbolt are that it takes significantly more skill to quickly and efficiently line up your cuts, and you cannot cut your stumps as low to the ground due to the downward-facing open angle. [1]

An example of an open-face cut in a back-leaning Red Maple.

The Open-Face undercut is essentially a mixture of the conventional and the Humbolt, with a wide open angle of 70 to 90 degrees. [6] This face cut is most commonly used in extreme scenarios where the tree in question has a severe back lean. The wide open angle of the cut allows the tree time to become upright, and then close as it falls without the two flat ends of the angle prematurely closing. The open face is fairly easy to master and line up correctly. [5] A couple big disadvantages are that it takes quite a bit more time to cut compared to a conventional or Humbolt, and there is waste left on both the stump and the log due to the angle being so open. It is not a common practice in the logging community and is much more frequently used in commercial tree work.

References

  1. ^ a b Gülci, Neşe; Gülci, Sercan; Akay, Abdullah E.; Sessions, John (2022-10-20). "A Comparison of Two Felling Techniques Considering Stump-Height-Related Timber Value Loss". Croatian Journal of Forest Engineering. 44 (1): 103–110. doi: 10.5552/crojfe.2023.1743. ISSN  1848-9672. S2CID  253050345.
  2. ^ Kawahara, Dairoku; Urabe, Yukio; Maeda, Noriaki; Sasadai, Junpei; Fujii, Eri; Moriyama, Nobuaki; Yamamoto, Takahiko; Iwata, Sho (2015). "The effect of different working postures while felling a tree with a chain-saw on trunk muscles' activity". Sangyo Eiseigaku Zasshi. 57 (4): 111–116. doi: 10.1539/sangyoeisei.b14016. ISSN  1341-0725. PMID  25995000.
  3. ^ Grzywiński, Witold; Jelonek, Tomasz; Tomczak, Arkadiusz; Jakubowski, Marcin; Bembenek, Mariusz (2017-09-21). "Does body posture during tree felling influence the physiological load of a chainsaw operator?". Annals of Agricultural and Environmental Medicine. 24 (3): 401–405. doi: 10.5604/12321966.1235177. ISSN  1232-1966. PMID  28954479.
  4. ^ Suhartana, S; Yuniawati (2019-10-01). "The Economic and Environmentally Friendly Tree Felling Techniques in Natural Forest". IOP Conference Series: Earth and Environmental Science. 359 (1): 012007. Bibcode: 2019E&ES..359a2007S. doi: 10.1088/1755-1315/359/1/012007. ISSN  1755-1307. S2CID  210620416.
  5. ^ a b c d e f Garland, John J. (1983). "Felling and Bucking Techniques for Woodland Owners". Oregon State University, Extension Service.
  6. ^ a b c d "How to make a directional notch". Husqvarna Chainsaw Academy. 2018-06-13. Retrieved 2023-05-08.
Retrieved from " https://en.wikipedia.org/?title=Hand_felling&oldid=1220729008"