A conventional electrical unit (or conventional unit where there is no risk of ambiguity) is a
unit of measurement in the field of
electricity which is based on the so-called "conventional values" of the
Josephson constant, the
von Klitzing constant agreed by the
International Committee for Weights and Measures (CIPM) in 1988, as well as
ΔνCs used to define the
second. These units are very similar in scale to their corresponding
SI units, but are not identical because of the different values used for the constants. They are distinguished from the corresponding SI units by setting the symbol in italic typeface and adding a subscript "90" – e.g., the conventional volt has the symbol V90 – as they came into international use on 1 January 1990.
This system was developed to increase the precision of measurements: The Josephson and von Klitzing constants can be realized with great precision, repeatability and ease, and are exactly defined in terms of the
universal constantse and
h. The conventional electrical units represent a significant step towards using "natural" fundamental physics for practical measurement purposes. They achieved acceptance as an international standard in parallel to the
SI system of units and are commonly used outside of the physics community in both engineering and industry. Addition of the constant
c would be needed to define units for all dimensions used in physics, as in the SI.
The SI system made the transition to equivalent definitions 29 years later but with values of the constants defined to match the old SI units more precisely. Consequently, the conventional electrical units differ slightly from the corresponding SI units,
now with exactly defined ratios.
Historical development
Several significant steps have been taken in the last half century to increase the precision and utility of measurement units:
In 1967, the thirteenth
General Conference on Weights and Measures (CGPM) defined the
second of atomic time in the International System of Units as the duration of 9192631770 periods of the radiation corresponding to the transition between the two
hyperfine levels of the ground state of the cesium-133 atom.[1]
In 1983, the seventeenth CGPM redefined the
metre in terms of the second and the speed of light, thus fixing the speed of light at exactly 299792458 m/s.[2]
In 1988, the CIPM recommended adoption of conventional values for the Josephson constant as exactly KJ-90 = 483597.9×109 Hz/V[3] and for the von Klitzing constant as exactly RK-90 = 25812.807 Ω[4] as of 1 January 1990.
In 1991, the eighteenth CGPM noted the conventional values for the Josephson constant and the von Klitzing constant.[5]
In 2000, the CIPM approved the use of the
quantum Hall effect, with the value of RK-90 to be used to establish a reference standard of resistance.[6]
In 2018, the twenty-sixth CGPM resolved to abrogate the conventional values of the Josephson and von Klitzing constants with the
2019 redefinition of SI base units.[7]
The conventional
volt, V90, is the electromotive force (or electric potential difference) measured against a
Josephson effect standard using the defined value of the Josephson constant, KJ-90; that is, by the relation KJ = 483597.9 GHz/V90. See
Josephson voltage standard.
The conventional
ohm, Ω90, is the electrical resistance measured against a
quantum Hall effect standard using the defined value of the von Klitzing constant, RK-90; that is, by the relation RK = 25812.807 Ω90.
Other conventional electrical units are defined by the normal relationships between units paralleling those of SI, as in the conversion table below.
The 2019 redefinition of SI base units defines all these units in a way that fixes the numeric values of KJ, RK and ΔνCs exactly, albeit with values of the first two that differ slightly from the conventional values. Consequently, these conventional units all have known exact values in terms of the redefined SI units. Because of this, there is no accuracy benefit from maintaining the conventional values.
^
ab
Mohr, Peter J.; Newell, David B.; Taylor, Barry N. (2015). "CODATA recommended values of the fundamental physical constants: 2014". Zenodo.
arXiv:1507.07956.
doi:
10.5281/zenodo.22826.