Colt-Burgess rifle | |
---|---|
Type | Lever-action rifle |
Place of origin | United States |
Production history | |
Designer | Andrew Burgess |
Manufacturer | Colt's Patent Firearms Manufacturing Company |
Produced | 1883–1885 |
No. built | 6,403 |
Specifications | |
Mass | 8+3⁄4 lb (4.0 kg) (octagon barrel rifle); 8+1⁄2 lb (3.9 kg) (round barrel rifle); 7+1⁄4 lb (3.3 kg) ( carbine) [1] |
Length | 42+3⁄4 in (1,090 mm) [1] |
Barrel length | 25+1⁄2 in (650 mm) (rifle); 20 in (510 mm) (carbine) |
Cartridge | .44-40 Winchester |
Action | Lever-action |
Feed system | 15 round (rifle) or 12 round (carbine) tubular magazine |
The Colt-Burgess rifle, also known as the 1883 Burgess rifle or simply the Burgess rifle, is a lever-action repeating rifle produced by Colt's Patent Firearms Manufacturing Company between 1883 and 1885. The Burgess rifle was Colt's only entrance into the lever-action rifle market, produced to compete with Winchester Repeating Arms Company's line of popular rifles. [2] [3] The 1883 Burgess rifle was designed and patented by Andrew Burgess, an American firearms designer and photographer, who sold the design to Colt. [4] [5]
The Colt-Burgess rifle is similar in design to Winchester's lever-action rifles, such as the Winchester Model 1873. It was produced in two versions chambered for the .44-40 Winchester cartridge: a rifle version with a 25+1⁄2 in (650 mm) barrel, and a carbine with a 20 in (510 mm) barrel. [2] The rifle features either a full octagon, half-octagon, or round barrel, with the full octagon barrels being the most numerously produced among rifle variants. [1] A tubular magazine is located under the barrel in similar fashion to other lever-action rifles with a capacity of 15 rounds in the rifle version or 12 rounds in the carbine version. The receiver on the Burgess rifle is smaller than the Winchester 1873's, providing for a lighter firearm. The rifle's action, though similar to the Winchester 1873's, is considered to be a stronger design. [1] [4] The action utilizes a toggle-joint system to lock the breechblock. The extension of the loading lever is the lower part of the toggle-joint; the upper part of the toggle-joint is linked to the breechblock. Located on the receiver is a sliding loading gate from which cartridges are fed into the magazine; the sliding gate design is in contrast to Winchester's tilting gate. Burgess rifles were finished with either a blued or browned barrel, blued receiver, casehardened hammer and lever, and walnut stock. Current reproduction Burgess rifles are also available with casehardened frames. [1] [3]
Although Colt predominantly was a manufacturer of popular revolvers, such as the Colt Single Action Army, the company began in the 1880s to seek to compete against Winchester in the rifle market. [5] In 1882, Colt contacted Andrew Burgess to design a lever-action rifle and by July 1883, production of the new rifle had begun. The Colt-Burgess was produced for sixteen months thereafter, with a total of 6,403 guns manufactured. Approximately 60% of these were of the rifle variation. [1] When compared to production figures of Winchester's 1873 rifle, the Colt-Burgess failed as a serious competitor to Winchester. From 1873 to 1919, Winchester manufactured 720,610 Model 1873 rifles, or an average of over 15,000 per year. [6]
The short production history of the Colt-Burgess has led to much speculation as to the reason of its demise. According to legend, upon hearing of Colt's entrance into the lever-action rifle market, Winchester began to develop a prototype revolver to compete with Colt's market. A " gentleman's agreement" then followed between Colt and Winchester, with Colt agreeing to drop production of the Burgess and Winchester abandoning its plans to develop a revolver. The truth of this story has never been fully verified, and as such, the reason for the Burgess rifle's short production history is unknown. [1] [4] [5]
Replicas of the Burgess rifle and carbine are currently produced by the Italian manufacturer Uberti chambered for the .45 Colt cartridge. [4] [7]