In
mathematics, an ellipse is a
plane curve surrounding two
focal points, such that for all points on the curve, the sum of the two distances to the focal points is a constant. It generalizes a
circle, which is the special type of ellipse in which the two focal points are the same. The elongation of an ellipse is measured by its
eccentricity$e$, a number ranging from $e=0$ (the
limiting case of a circle) to $e=1$ (the limiting case of infinite elongation, no longer an ellipse but a
parabola).
An ellipse has a simple
algebraic solution for its area, but only approximations for its
perimeter (also known as
circumference), for which integration is required to obtain an exact solution.
Analytically, the equation of a standard ellipse centered at the origin with width $2a$ and height $2b$ is:
Ellipses are the
closed type of
conic section: a plane curve tracing the intersection of a
cone with a
plane (see figure). Ellipses have many similarities with the other two forms of conic sections, parabolas and
hyperbolas, both of which are
open and
unbounded. An angled
cross section of a right circular
cylinder is also an ellipse.
An ellipse may also be defined in terms of one focal point and a line outside the ellipse called the
directrix: for all points on the ellipse, the ratio between the distance to the
focus and the distance to the directrix is a constant. This constant ratio is the above-mentioned eccentricity:
Ellipses are common in
physics,
astronomy and
engineering. For example, the
orbit of each planet in the
Solar System is approximately an ellipse with the Sun at one focus point (more precisely, the focus is the
barycenter of the Sun–planet pair). The same is true for moons orbiting planets and all other systems of two astronomical bodies. The shapes of planets and stars are often well described by
ellipsoids. A circle viewed from a side angle looks like an ellipse: that is, the ellipse is the image of a circle under
parallel or
perspective projection. The ellipse is also the simplest
Lissajous figure formed when the horizontal and vertical motions are
sinusoids with the same frequency: a similar effect leads to
elliptical polarization of light in
optics.
The name, ἔλλειψις (élleipsis, "omission"), was given by
Apollonius of Perga in his Conics.
Definition as locus of points
An ellipse can be defined geometrically as a set or
locus of points in the Euclidean plane:
Given two fixed points $F_{1},F_{2}$ called the foci and a distance $2a$ which is greater than the distance between the foci, the ellipse is the set of points $P$ such that the sum of the distances $|PF_{1}|,\ |PF_{2}|$ is equal to $2a$:
The midpoint $C$ of the line segment joining the foci is called the center of the ellipse. The line through the foci is called the major axis, and the line perpendicular to it through the center is the minor axis. The major axis intersects the ellipse at two vertices$V_{1},V_{2}$, which have distance $a$ to the center. The distance $c$ of the foci to the center is called the focal distance or linear eccentricity. The quotient $e={\tfrac {c}{a}}$ is the eccentricity.
The case $F_{1}=F_{2}$ yields a circle and is included as a special type of ellipse.
The equation $\left|PF_{2}\right|+\left|PF_{1}\right|=2a$ can be viewed in a different way (see figure):
If $c_{2}$ is the circle with center $F_{2}$ and radius $2a$, then the distance of a point $P$ to the circle $c_{2}$ equals the distance to the focus $F_{1}$:
$\left|PF_{1}\right|=\left|Pc_{2}\right|.$
$c_{2}$ is called the circular directrix (related to focus $F_{2}$) of the ellipse.^{
[1]}^{
[2]} This property should not be confused with the definition of an ellipse using a directrix line below.
Using
Dandelin spheres, one can prove that any section of a cone with a plane is an ellipse, assuming the plane does not contain the apex and has slope less than that of the lines on the cone.
In Cartesian coordinates
Standard equation
The standard form of an ellipse in Cartesian coordinates assumes that the origin is the center of the ellipse, the x-axis is the major axis, and:
the foci are the points $F_{1}=(c,\,0),\ F_{2}=(-c,\,0)$,
the vertices are $V_{1}=(a,\,0),\ V_{2}=(-a,\,0)$.
For an arbitrary point $(x,y)$ the distance to the focus $(c,0)$ is ${\textstyle {\sqrt {(x-c)^{2}+y^{2}}}}$ and to the other focus ${\textstyle {\sqrt {(x+c)^{2}+y^{2}}}}$. Hence the point $(x,\,y)$ is on the ellipse whenever:
The width and height parameters $a,\;b$ are called the
semi-major and semi-minor axes. The top and bottom points $V_{3}=(0,\,b),\;V_{4}=(0,\,-b)$ are the co-vertices. The distances from a point $(x,\,y)$ on the ellipse to the left and right foci are $a+ex$ and $a-ex$.
It follows from the equation that the ellipse is symmetric with respect to the coordinate axes and hence with respect to the origin.
In principle, the canonical ellipse equation ${\tfrac {x^{2}}{a^{2}}}+{\tfrac {y^{2}}{b^{2}}}=1$ may have $a<b$ (and hence the ellipse would be taller than it is wide). This form can be converted to the standard form by transposing the variable names $x$ and $y$ and the parameter names $a$ and $b.$
Linear eccentricity
This is the distance from the center to a focus: $c={\sqrt {a^{2}-b^{2}}}$.
assuming $a>b.$ An ellipse with equal axes ($a=b$) has zero eccentricity, and is a circle.
Semi-latus rectum
The length of the chord through one focus, perpendicular to the major axis, is called the latus rectum. One half of it is the semi-latus rectum$\ell$. A calculation shows:^{
[4]}
An arbitrary line $g$ intersects an ellipse at 0, 1, or 2 points, respectively called an exterior line, tangent and secant. Through any point of an ellipse there is a unique tangent. The tangent at a point $(x_{1},\,y_{1})$ of the ellipse ${\tfrac {x^{2}}{a^{2}}}+{\tfrac {y^{2}}{b^{2}}}=1$ has the coordinate equation:
Proof:
Let $(x_{1},\,y_{1})$ be a point on an ellipse and ${\textstyle {\vec {x}}={\begin{pmatrix}x_{1}\\y_{1}\end{pmatrix}}+s{\begin{pmatrix}u\\v\end{pmatrix}}}$ be the equation of any line $g$ containing $(x_{1},\,y_{1})$. Inserting the line's equation into the ellipse equation and respecting ${\textstyle {\frac {x_{1}^{2}}{a^{2}}}+{\frac {y_{1}^{2}}{b^{2}}}=1}$ yields:
${\frac {x_{1}}{a^{2}}}u+{\frac {y_{1}}{b^{2}}}v=0.$ Then line $g$ and the ellipse have only point $(x_{1},\,y_{1})$ in common, and $g$ is a tangent. The tangent direction has
perpendicular vector${\begin{pmatrix}{\frac {x_{1}}{a^{2}}}&{\frac {y_{1}}{b^{2}}}\end{pmatrix}}$, so the tangent line has equation ${\textstyle {\frac {x_{1}}{a^{2}}}x+{\tfrac {y_{1}}{b^{2}}}y=k}$ for some $k$. Because $(x_{1},\,y_{1})$ is on the tangent and the ellipse, one obtains $k=1$.
${\frac {x_{1}}{a^{2}}}u+{\frac {y_{1}}{b^{2}}}v\neq 0.$ Then line $g$ has a second point in common with the ellipse, and is a secant.
Using (1) one finds that ${\begin{pmatrix}-y_{1}a^{2}&x_{1}b^{2}\end{pmatrix}}$ is a tangent vector at point $(x_{1},\,y_{1})$, which proves the vector equation.
If $(x_{1},y_{1})$ and $(u,v)$ are two points of the ellipse such that ${\textstyle {\frac {x_{1}u}{a^{2}}}+{\tfrac {y_{1}v}{b^{2}}}=0}$, then the points lie on two conjugate diameters (see
below). (If $a=b$, the ellipse is a circle and "conjugate" means "orthogonal".)
Shifted ellipse
If the standard ellipse is shifted to have center $\left(x_{\circ },\,y_{\circ }\right)$, its equation is
Then the ellipse is a non-degenerate real ellipse if and only if C∆ < 0. If C∆ > 0, we have an imaginary ellipse, and if ∆ = 0, we have a point ellipse.^{
[7]}^{: 63 }
The general equation's coefficients can be obtained from known semi-major axis $a$, semi-minor axis $b$, center coordinates $\left(x_{\circ },\,y_{\circ }\right)$, and rotation angle $\theta$ (the angle from the positive horizontal axis to the ellipse's major axis) using the formulae:
which covers any point of the ellipse ${\tfrac {x^{2}}{a^{2}}}+{\tfrac {y^{2}}{b^{2}}}=1$ except the left vertex $(-a,\,0)$.
For $u\in [0,\,1],$ this formula represents the right upper quarter of the ellipse moving counter-clockwise with increasing $u.$ The left vertex is the limit ${\textstyle \lim _{u\to \pm \infty }(x(u),\,y(u))=(-a,\,0)\;.}$
Alternately, if the parameter $[u:v]$ is considered to be a point on the
real projective line${\textstyle \mathbf {P} (\mathbf {R} )}$, then the corresponding rational parametrization is
A parametric representation, which uses the slope $m$ of the tangent at a point of the ellipse
can be obtained from the derivative of the standard representation ${\vec {x}}(t)=(a\cos t,\,b\sin t)^{\mathsf {T}}$:
Here $m$ is the slope of the tangent at the corresponding ellipse point, ${\vec {c}}_{+}$ is the upper and ${\vec {c}}_{-}$ the lower half of the ellipse. The vertices$(\pm a,\,0)$, having vertical tangents, are not covered by the representation.
The equation of the tangent at point ${\vec {c}}_{\pm }(m)$ has the form $y=mx+n$. The still unknown $n$ can be determined by inserting the coordinates of the corresponding ellipse point ${\vec {c}}_{\pm }(m)$:
$y=mx\pm {\sqrt {m^{2}a^{2}+b^{2}}}\,.$
This description of the tangents of an ellipse is an essential tool for the determination of the
orthoptic of an ellipse. The orthoptic article contains another proof, without differential calculus and trigonometric formulae.
Any ellipse is an affine image of the unit circle with equation $x^{2}+y^{2}=1$.
Parametric representation
An affine transformation of the Euclidean plane has the form ${\vec {x}}\mapsto {\vec {f}}\!_{0}+A{\vec {x}}$, where $A$ is a regular
matrix (with non-zero
determinant) and ${\vec {f}}\!_{0}$ is an arbitrary vector. If ${\vec {f}}\!_{1},{\vec {f}}\!_{2}$ are the column vectors of the matrix $A$, the unit circle $(\cos(t),\sin(t))$, $0\leq t\leq 2\pi$, is mapped onto the ellipse:
Here ${\vec {f}}\!_{0}$ is the center and ${\vec {f}}\!_{1},\;{\vec {f}}\!_{2}$ are the directions of two
conjugate diameters, in general not perpendicular.
Vertices
The four vertices of the ellipse are ${\vec {p}}(t_{0}),\;{\vec {p}}\left(t_{0}\pm {\tfrac {\pi }{2}}\right),\;{\vec {p}}\left(t_{0}+\pi \right)$, for a parameter $t=t_{0}$ defined by:
With the abbreviations
$\;M={\vec {f}}_{1}^{2}+{\vec {f}}_{2}^{2},\ N=\left|\det({\vec {f}}_{1},{\vec {f}}_{2})\right|$ the statements of Apollonios's theorem can be written as:
$a^{2}+b^{2}=M,\quad ab=N\ .$
Solving this nonlinear system for $a,b$ yields the semiaxes:
Solving the parametric representation for $\;\cos t,\sin t\;$ by
Cramer's rule and using $\;\cos ^{2}t+\sin ^{2}t-1=0\;$, one obtains the implicit representation
For ${\vec {f}}_{0}={0 \choose 0},\;{\vec {f}}_{1}=a{\cos \theta \choose \sin \theta },\;{\vec {f}}_{2}=b{-\sin \theta \choose \;\cos \theta }$ one obtains a parametric representation of the standard ellipse
rotated by angle $\theta$:
The definition of an ellipse in this section gives a parametric representation of an arbitrary ellipse, even in space, if one allows ${\vec {f}}\!_{0},{\vec {f}}\!_{1},{\vec {f}}\!_{2}$ to be vectors in space.
Polar forms
Polar form relative to center
In
polar coordinates, with the origin at the center of the ellipse and with the angular coordinate $\theta$ measured from the major axis, the ellipse's equation is^{
[7]}^{: 75 }
If instead we use polar coordinates with the origin at one focus, with the angular coordinate $\theta =0$ still measured from the major axis, the ellipse's equation is
where the sign in the denominator is negative if the reference direction $\theta =0$ points towards the center (as illustrated on the right), and positive if that direction points away from the center.
In the slightly more general case of an ellipse with one focus at the origin and the other focus at angular coordinate $\phi$, the polar form is
The angle $\theta$ in these formulas is called the
true anomaly of the point. The numerator of these formulas is the
semi-latus rectum$\ell =a(1-e^{2})$.
Eccentricity and the directrix property
Each of the two lines parallel to the minor axis, and at a distance of ${\textstyle d={\frac {a^{2}}{c}}={\frac {a}{e}}}$ from it, is called a directrix of the ellipse (see diagram).
For an arbitrary point $P$ of the ellipse, the quotient of the distance to one focus and to the corresponding directrix (see diagram) is equal to the eccentricity:
The proof for the pair $F_{1},l_{1}$ follows from the fact that ${\textstyle \left|PF_{1}\right|^{2}=(x-c)^{2}+y^{2},\ \left|Pl_{1}\right|^{2}=\left(x-{\tfrac {a^{2}}{c}}\right)^{2}}$ and $y^{2}=b^{2}-{\tfrac {b^{2}}{a^{2}}}x^{2}$ satisfy the equation
The converse is also true and can be used to define an ellipse (in a manner similar to the definition of a parabola):
For any point $F$ (focus), any line $l$ (directrix) not through $F$, and any real number $e$ with $0<e<1,$ the ellipse is the locus of points for which the quotient of the distances to the point and to the line is $e,$ that is:
The extension to $e=0$, which is the eccentricity of a circle, is not allowed in this context in the Euclidean plane. However, one may consider the directrix of a circle to be the
line at infinity in the
projective plane.
(The choice $e=1$ yields a parabola, and if $e>1$, a hyperbola.)
Proof
Let $F=(f,\,0),\ e>0$, and assume $(0,\,0)$ is a point on the curve. The directrix $l$ has equation $x=-{\tfrac {f}{e}}$. With $P=(x,\,y)$, the relation $|PF|^{2}=e^{2}|Pl|^{2}$ produces the equations
$(x-f)^{2}+y^{2}=e^{2}\left(x+{\frac {f}{e}}\right)^{2}=(ex+f)^{2}$ and $x^{2}\left(e^{2}-1\right)+2xf(1+e)-y^{2}=0.$
The substitution $p=f(1+e)$ yields
$x^{2}\left(e^{2}-1\right)+2px-y^{2}=0.$
This is the equation of an ellipse ($e<1$), or a parabola ($e=1$), or a hyperbola ($e>1$). All of these non-degenerate conics have, in common, the origin as a vertex (see diagram).
If $e<1$, introduce new parameters $a,\,b$ so that $1-e^{2}={\tfrac {b^{2}}{a^{2}}},{\text{ and }}\ p={\tfrac {b^{2}}{a}}$, and then the equation above becomes
which is the equation of an ellipse with center $(a,\,0)$, the x-axis as major axis, and
the major/minor semi axis $a,\,b$.
Construction of a directrix
Because of $c\cdot {\tfrac {a^{2}}{c}}=a^{2}$ point $L_{1}$ of directrix $l_{1}$ (see diagram) and focus $F_{1}$ are inverse with respect to the
circle inversion at circle $x^{2}+y^{2}=a^{2}$ (in diagram green). Hence $L_{1}$ can be constructed as shown in the diagram. Directrix $l_{1}$ is the perpendicular to the main axis at point $L_{1}$.
General ellipse
If the focus is $F=\left(f_{1},\,f_{2}\right)$ and the directrix $ux+vy+w=0$, one obtains the equation
(The right side of the equation uses the
Hesse normal form of a line to calculate the distance $|Pl|$.)
Focus-to-focus reflection property
An ellipse possesses the following property:
The normal at a point $P$ bisects the angle between the lines ${\overline {PF_{1}}},\,{\overline {PF_{2}}}$.
Proof
Because the tangent line is perpendicular to the normal, an equivalent statement is that the tangent is the external angle bisector of the lines to the foci (see diagram).
Let $L$ be the point on the line ${\overline {PF_{2}}}$ with distance $2a$ to the focus $F_{2}$, where $a$ is the semi-major axis of the ellipse. Let line $w$ be the external angle bisector of the lines ${\overline {PF_{1}}}$ and ${\overline {PF_{2}}}.$ Take any other point $Q$ on $w.$ By the
triangle inequality and the
angle bisector theorem, $2a=\left|LF_{2}\right|<{}$$\left|QF_{2}\right|+\left|QL\right|={}$$\left|QF_{2}\right|+\left|QF_{1}\right|,$ therefore $Q$ must be outside the ellipse. As this is true for every choice of $Q,$$w$ only intersects the ellipse at the single point $P$ so must be the tangent line.
Application
The rays from one focus are reflected by the ellipse to the second focus. This property has optical and acoustic applications similar to the reflective property of a parabola (see
whispering gallery).
The midpoints of parallel chords lie on a diameter.
An affine transformation preserves parallelism and midpoints of line segments, so this property is true for any ellipse. (Note that the parallel chords and the diameter are no longer orthogonal.)
Definition
Two diameters $d_{1},\,d_{2}$ of an ellipse are conjugate if the midpoints of chords parallel to $d_{1}$ lie on $d_{2}\ .$
From the diagram one finds:
Two diameters ${\overline {P_{1}Q_{1}}},\,{\overline {P_{2}Q_{2}}}$ of an ellipse are conjugate whenever the tangents at $P_{1}$ and $Q_{1}$ are parallel to ${\overline {P_{2}Q_{2}}}$.
Conjugate diameters in an ellipse generalize orthogonal diameters in a circle.
In the parametric equation for a general ellipse given above,
any pair of points ${\vec {p}}(t),\ {\vec {p}}(t+\pi )$ belong to a diameter, and the pair ${\vec {p}}\left(t+{\tfrac {\pi }{2}}\right),\ {\vec {p}}\left(t-{\tfrac {\pi }{2}}\right)$ belong to its conjugate diameter.
For the common parametric representation $(a\cos t,b\sin t)$ of the ellipse with equation ${\tfrac {x^{2}}{a^{2}}}+{\tfrac {y^{2}}{b^{2}}}=1$ one gets: The points
$(x_{1},y_{1})=(\pm a\cos t,\pm b\sin t)\quad$ (signs: (+,+) or (−,−) )
In case of a circle the last equation collapses to $x_{1}x_{2}+y_{1}y_{2}=0\ .$
Theorem of Apollonios on conjugate diameters
For an ellipse with semi-axes $a,\,b$ the following is true:^{
[9]}^{
[10]}
Let $c_{1}$ and $c_{2}$ be halves of two conjugate diameters (see diagram) then
$c_{1}^{2}+c_{2}^{2}=a^{2}+b^{2}$.
The triangle$O,P_{1},P_{2}$ with sides $c_{1},\,c_{2}$ (see diagram) has the constant area ${\textstyle A_{\Delta }={\frac {1}{2}}ab}$, which can be expressed by $A_{\Delta }={\tfrac {1}{2}}c_{2}d_{1}={\tfrac {1}{2}}c_{1}c_{2}\sin \alpha$, too. $d_{1}$ is the altitude of point $P_{1}$ and $\alpha$ the angle between the half diameters. Hence the area of the ellipse (see section
metric properties) can be written as $A_{el}=\pi ab=\pi c_{2}d_{1}=\pi c_{1}c_{2}\sin \alpha$.
The parallelogram of tangents adjacent to the given conjugate diameters has the ${\text{Area}}_{12}=4ab\ .$
Proof
Let the ellipse be in the canonical form with parametric equation
${\vec {p}}(t)=(a\cos t,\,b\sin t).$
The two points ${\textstyle {\vec {c}}_{1}={\vec {p}}(t),\ {\vec {c}}_{2}={\vec {p}}\left(t+{\frac {\pi }{2}}\right)}$ are on conjugate diameters (see previous section). From trigonometric formulae one obtains ${\vec {c}}_{2}=(-a\sin t,\,b\cos t)^{\mathsf {T}}$ and
For the ellipse ${\tfrac {x^{2}}{a^{2}}}+{\tfrac {y^{2}}{b^{2}}}=1$ the intersection points of orthogonal tangents lie on the circle $x^{2}+y^{2}=a^{2}+b^{2}$.
This circle is called orthoptic or
director circle of the ellipse (not to be confused with the circular directrix defined above).
Drawing ellipses
Ellipses appear in
descriptive geometry as images (parallel or central projection) of circles. There exist various tools to draw an ellipse. Computers provide the fastest and most accurate method for drawing an ellipse. However, technical tools (ellipsographs) to draw an ellipse without a computer exist. The principle of ellipsographs were known to Greek mathematicians such as
Archimedes and
Proklos.
For any method described below, knowledge of the axes and the semi-axes is necessary (or equivalently: the foci and the semi-major axis). If this presumption is not fulfilled one has to know at least two conjugate diameters. With help of
Rytz's construction the axes and semi-axes can be retrieved.
de La Hire's point construction
The following construction of single points of an ellipse is due to
de La Hire.^{
[11]} It is based on the
standard parametric representation$(a\cos t,\,b\sin t)$ of an ellipse:
Draw the two circles centered at the center of the ellipse with radii $a,b$ and the axes of the ellipse.
Draw a line through the center, which intersects the two circles at point $A$ and $B$, respectively.
Draw a line through $A$ that is parallel to the minor axis and a line through $B$ that is parallel to the major axis. These lines meet at an ellipse point (see diagram).
Repeat steps (2) and (3) with different lines through the center.
de La Hire's method
Animation of the method
Pins-and-string method
The characterization of an ellipse as the locus of points so that sum of the distances to the foci is constant leads to a method of drawing one using two
drawing pins, a length of string, and a pencil. In this method, pins are pushed into the paper at two points, which become the ellipse's foci. A string is tied at each end to the two pins; its length after tying is $2a$. The tip of the pencil then traces an ellipse if it is moved while keeping the string taut. Using two pegs and a rope, gardeners use this procedure to outline an elliptical flower bed—thus it is called the gardener's ellipse.
This representation can be modeled technically by two simple methods. In both cases center, the axes and semi axes $a,\,b$ have to be known.
Method 1
The first method starts with
a strip of paper of length $a+b$.
The point, where the semi axes meet is marked by $P$. If the strip slides with both ends on the axes of the desired ellipse, then point $P$ traces the ellipse. For the proof one shows that point $P$ has the parametric representation $(a\cos t,\,b\sin t)$, where parameter $t$ is the angle of the slope of the paper strip.
A technical realization of the motion of the paper strip can be achieved by a
Tusi couple (see animation). The device is able to draw any ellipse with a fixed sum $a+b$, which is the radius of the large circle. This restriction may be a disadvantage in real life. More flexible is the second paper strip method.
Ellipse construction: paper strip method 1
Ellipses with Tusi couple. Two examples: red and cyan.
A variation of the paper strip method 1 uses the observation that the midpoint $N$ of the paper strip is moving on the circle with center $M$ (of the ellipse) and radius ${\tfrac {a+b}{2}}$. Hence, the paperstrip can be cut at point $N$ into halves, connected again by a joint at $N$ and the sliding end $K$ fixed at the center $M$ (see diagram). After this operation the movement of the unchanged half of the paperstrip is unchanged.^{
[12]} This variation requires only one sliding shoe.
Variation of the paper strip method 1
Animation of the variation of the paper strip method 1
Method 2
The second method starts with
a strip of paper of length $a$.
One marks the point, which divides the strip into two substrips of length $b$ and $a-b$. The strip is positioned onto the axes as described in the diagram. Then the free end of the strip traces an ellipse, while the strip is moved. For the proof, one recognizes that the tracing point can be described parametrically by $(a\cos t,\,b\sin t)$, where parameter $t$ is the angle of slope of the paper strip.
This method is the base for several ellipsographs (see section below).
Similar to the variation of the paper strip method 1 a variation of the paper strip method 2 can be established (see diagram) by cutting the part between the axes into halves.
Most ellipsograph
drafting instruments are based on the second paperstrip method.
Approximation by osculating circles
From Metric properties below, one obtains:
The radius of curvature at the vertices $V_{1},\,V_{2}$ is: ${\tfrac {b^{2}}{a}}$
The radius of curvature at the co-vertices $V_{3},\,V_{4}$ is: ${\tfrac {a^{2}}{b}}\ .$
The diagram shows an easy way to find the centers of curvature $C_{1}=\left(a-{\tfrac {b^{2}}{a}},0\right),\,C_{3}=\left(0,b-{\tfrac {a^{2}}{b}}\right)$ at vertex $V_{1}$ and co-vertex $V_{3}$, respectively:
mark the auxiliary point $H=(a,\,b)$ and draw the line segment $V_{1}V_{3}\ ,$
draw the line through $H$, which is perpendicular to the line $V_{1}V_{3}\ ,$
the intersection points of this line with the axes are the centers of the osculating circles.
(proof: simple calculation.)
The centers for the remaining vertices are found by symmetry.
Given two
pencils$B(U),\,B(V)$ of lines at two points $U,\,V$ (all lines containing $U$ and $V$, respectively) and a projective but not perspective mapping $\pi$ of $B(U)$ onto $B(V)$, then the intersection points of corresponding lines form a non-degenerate projective conic section.
For the generation of points of the ellipse ${\tfrac {x^{2}}{a^{2}}}+{\tfrac {y^{2}}{b^{2}}}=1$ one uses the pencils at the vertices $V_{1},\,V_{2}$. Let $P=(0,\,b)$ be an upper co-vertex of the ellipse and $A=(-a,\,2b),\,B=(a,\,2b)$.
$P$ is the center of the rectangle $V_{1},\,V_{2},\,B,\,A$. The side ${\overline {AB}}$ of the rectangle is divided into n equal spaced line segments and this division is projected parallel with the diagonal $AV_{2}$ as direction onto the line segment ${\overline {V_{1}B}}$ and assign the division as shown in the diagram. The parallel projection together with the reverse of the orientation is part of the projective mapping between the pencils at $V_{1}$ and $V_{2}$ needed. The intersection points of any two related lines $V_{1}B_{i}$ and $V_{2}A_{i}$ are points of the uniquely defined ellipse. With help of the points $C_{1},\,\dotsc$ the points of the second quarter of the ellipse can be determined. Analogously one obtains the points of the lower half of the ellipse.
Steiner generation can also be defined for hyperbolas and parabolas. It is sometimes called a parallelogram method because one can use other points rather than the vertices, which starts with a parallelogram instead of a rectangle.
As hypotrochoid
The ellipse is a special case of the
hypotrochoid when $R=2r$, as shown in the adjacent image. The special case of a moving circle with radius $r$ inside a circle with radius $R=2r$ is called a
Tusi couple.
Inscribed angles and three-point form
Circles
A circle with equation $\left(x-x_{\circ }\right)^{2}+\left(y-y_{\circ }\right)^{2}=r^{2}$ is uniquely determined by three points $\left(x_{1},y_{1}\right),\;\left(x_{2},\,y_{2}\right),\;\left(x_{3},\,y_{3}\right)$ not on a line. A simple way to determine the parameters $x_{\circ },y_{\circ },r$ uses the inscribed angle theorem for circles:
For four points $P_{i}=\left(x_{i},\,y_{i}\right),\ i=1,\,2,\,3,\,4,\,$ (see diagram) the following statement is true:
The four points are on a circle if and only if the angles at $P_{3}$ and $P_{4}$ are equal.
Usually one measures inscribed angles by a degree or radian θ, but here the following measurement is more convenient:
In order to measure the angle between two lines with equations $y=m_{1}x+d_{1},\ y=m_{2}x+d_{2},\ m_{1}\neq m_{2},$ one uses the quotient:
This section considers the family of ellipses defined by equations ${\tfrac {\left(x-x_{\circ }\right)^{2}}{a^{2}}}+{\tfrac {\left(y-y_{\circ }\right)^{2}}{b^{2}}}=1$ with a fixed eccentricity $e$. It is convenient to use the parameter:
where q is fixed and $x_{\circ },\,y_{\circ },\,a$ vary over the real numbers. (Such ellipses have their axes parallel to the coordinate axes: if $q<1$, the major axis is parallel to the x-axis; if $q>1$, it is parallel to the y-axis.)
Like a circle, such an ellipse is determined by three points not on a line.
For this family of ellipses, one introduces the following
q-analog angle measure, which is not a function of the usual angle measure θ:^{
[13]}^{
[14]}
In order to measure an angle between two lines with equations $y=m_{1}x+d_{1},\ y=m_{2}x+d_{2},\ m_{1}\neq m_{2}$ one uses the quotient:
Given four points $P_{i}=\left(x_{i},\,y_{i}\right),\ i=1,\,2,\,3,\,4$, no three of them on a line (see diagram).
The four points are on an ellipse with equation $(x-x_{\circ })^{2}+{\color {blue}q}\,(y-y_{\circ })^{2}=a^{2}$ if and only if the angles at $P_{3}$ and $P_{4}$ are equal in the sense of the measurement above—that is, if
At first the measure is available only for chords which are not parallel to the y-axis. But the final formula works for any chord. The proof follows from a straightforward calculation. For the direction of proof given that the points are on an ellipse, one can assume that the center of the ellipse is the origin.
Three-point form of ellipse equation
A consequence, one obtains an equation for the ellipse determined by three non-collinear points $P_{i}=\left(x_{i},\,y_{i}\right)$:
where $*$ is the modified
dot product${\vec {u}}*{\vec {v}}=u_{x}v_{x}+{\color {blue}q}\,u_{y}v_{y}.$
Pole-polar relation
Any ellipse can be described in a suitable coordinate system by an equation ${\tfrac {x^{2}}{a^{2}}}+{\tfrac {y^{2}}{b^{2}}}=1$. The equation of the tangent at a point $P_{1}=\left(x_{1},\,y_{1}\right)$ of the ellipse is ${\tfrac {x_{1}x}{a^{2}}}+{\tfrac {y_{1}y}{b^{2}}}=1.$ If one allows point $P_{1}=\left(x_{1},\,y_{1}\right)$ to be an arbitrary point different from the origin, then
point $P_{1}=\left(x_{1},\,y_{1}\right)\neq (0,\,0)$ is mapped onto the line ${\tfrac {x_{1}x}{a^{2}}}+{\tfrac {y_{1}y}{b^{2}}}=1$, not through the center of the ellipse.
This relation between points and lines is a
bijection.
line $y=mx+d,\ d\neq 0$ onto the point $\left(-{\tfrac {ma^{2}}{d}},\,{\tfrac {b^{2}}{d}}\right)$ and
line $x=c,\ c\neq 0$ onto the point $\left({\tfrac {a^{2}}{c}},\,0\right).$
Such a relation between points and lines generated by a conic is called pole-polar relation or polarity. The pole is the point; the polar the line.
By calculation one can confirm the following properties of the pole-polar relation of the ellipse:
For a point (pole) on the ellipse, the polar is the tangent at this point (see diagram: $P_{1},\,p_{1}$).
For a pole $P$outside the ellipse, the intersection points of its polar with the ellipse are the tangency points of the two tangents passing $P$ (see diagram: $P_{2},\,p_{2}$).
For a point within the ellipse, the polar has no point with the ellipse in common (see diagram: $F_{1},\,l_{1}$).
The intersection point of two polars is the pole of the line through their poles.
The foci $(c,\,0)$ and $(-c,\,0)$, respectively, and the directrices $x={\tfrac {a^{2}}{c}}$ and $x=-{\tfrac {a^{2}}{c}}$, respectively, belong to pairs of pole and polar. Because they are even polar pairs with respect to the circle $x^{2}+y^{2}=a^{2}$, the directrices can be constructed by compass and straightedge (see
Inversive geometry).
Pole-polar relations exist for hyperbolas and parabolas as well.
Metric properties
All metric properties given below refer to an ellipse with equation
${\frac {x^{2}}{a^{2}}}+{\frac {y^{2}}{b^{2}}}=1$
(1)
except for the section on the area enclosed by a tilted ellipse, where the generalized form of Eq.(1) will be given.
Area
The
area$A_{\text{ellipse}}$ enclosed by an ellipse is:
$A_{\text{ellipse}}=\pi ab$
(2)
where $a$ and $b$ are the lengths of the semi-major and semi-minor axes, respectively. The area formula $\pi ab$ is intuitive: start with a circle of radius $b$ (so its area is $\pi b^{2}$) and stretch it by a factor $a/b$ to make an ellipse. This scales the area by the same factor: $\pi b^{2}(a/b)=\pi ab.$^{
[15]} However, using the same approach for the circumference would be fallacious – compare the
integrals${\textstyle \int f(x)\,dx}$ and ${\textstyle \int {\sqrt {1+f'^{2}(x)}}\,dx}$. It is also easy to rigorously prove the area formula using integration as follows. Equation (1) can be rewritten as ${\textstyle y(x)=b{\sqrt {1-x^{2}/a^{2}}}.}$ For $x\in [-a,a],$ this curve is the top half of the ellipse. So twice the integral of $y(x)$ over the interval $[-a,a]$ will be the area of the ellipse:
An ellipse defined implicitly by $Ax^{2}+Bxy+Cy^{2}=1$ has area $2\pi /{\sqrt {4AC-B^{2}}}.$
The area can also be expressed in terms of eccentricity and the length of the semi-major axis as $a^{2}\pi {\sqrt {1-e^{2}}}$ (obtained by solving for
flattening, then computing the semi-minor axis).
So far we have dealt with erect ellipses, whose major and minor axes are parallel to the $x$ and $y$ axes. However, some applications require tilted ellipses. In charged-particle beam optics, for instance, the enclosed area of an erect or tilted ellipse is an important property of the beam, its emittance. In this case a simple formula still applies, namely
where $y_{\text{int}}$, $x_{\text{int}}$ are intercepts and $x_{\text{max}}$, $y_{\text{max}}$ are maximum values. It follows directly from
Apollonios's theorem.
where again $a$ is the length of the semi-major axis, ${\textstyle e={\sqrt {1-b^{2}/a^{2}}}}$ is the eccentricity, and the function $E$ is the
complete elliptic integral of the second kind,
The circumference of the ellipse may be evaluated in terms of $E(e)$ using
Gauss's arithmetic-geometric mean;^{
[16]} this is a quadratically converging iterative method (see
here for details).
where $n!!$ is the
double factorial (extended to negative odd integers by the recurrence relation $(2n-1)!!=(2n+1)!!/(2n+1)$, for $n\leq 0$). This series converges, but by expanding in terms of $h=(a-b)^{2}/(a+b)^{2},$James Ivory^{
[17]} and Bessel^{
[18]} derived an expression that converges much more rapidly:
where $h$ takes on the same meaning as above. The errors in these approximations, which were obtained empirically, are of order $h^{3}$ and $h^{5},$ respectively.
More generally, the
arc length of a portion of the circumference, as a function of the angle subtended (or x coordinates of any two points on the upper half of the ellipse), is given by an incomplete
elliptic integral. The upper half of an ellipse is parameterized by
$y=b\ {\sqrt {1-{\frac {x^{2}}{a^{2}}}\ }}~.$
Then the arc length $s$ from $\ x_{1}\$ to $\ x_{2}\$ is:
Here the upper bound $\ 2\pi a\$ is the circumference of a
circumscribedconcentric circle passing through the endpoints of the ellipse's major axis, and the lower bound $4{\sqrt {a^{2}+b^{2}}}$ is the perimeter of an
inscribedrhombus with
vertices at the endpoints of the major and the minor axes.
Curvature
The
curvature is given by $\kappa ={\frac {1}{a^{2}b^{2}}}\left({\frac {x^{2}}{a^{4}}}+{\frac {y^{2}}{b^{4}}}\right)^{-{\frac {3}{2}}}\ ,$radius of curvature at point $(x,y)$:
If the water's surface is disturbed at one focus of an elliptical water tank, the circular waves of that disturbance, after
reflecting off the walls, converge simultaneously to a single point: the second focus. This is a consequence of the total travel length being the same along any wall-bouncing path between the two foci.
Similarly, if a light source is placed at one focus of an elliptic
mirror, all light rays on the plane of the ellipse are reflected to the second focus. Since no other smooth curve has such a property, it can be used as an alternative definition of an ellipse. (In the special case of a circle with a source at its center all light would be reflected back to the center.) If the ellipse is rotated along its major axis to produce an ellipsoidal mirror (specifically, a
prolate spheroid), this property holds for all rays out of the source. Alternatively, a cylindrical mirror with elliptical cross-section can be used to focus light from a linear
fluorescent lamp along a line of the paper; such mirrors are used in some
document scanners.
Sound waves are reflected in a similar way, so in a large elliptical room a person standing at one focus can hear a person standing at the other focus remarkably well. The effect is even more evident under a
vaulted roof shaped as a section of a prolate spheroid. Such a room is called a whisper chamber. The same effect can be demonstrated with two reflectors shaped like the end caps of such a spheroid, placed facing each other at the proper distance. Examples are the
National Statuary Hall at the
United States Capitol (where
John Quincy Adams is said to have used this property for eavesdropping on political matters); the
Mormon Tabernacle at
Temple Square in
Salt Lake City,
Utah; at an exhibit on sound at the
Museum of Science and Industry in
Chicago; in front of the
University of Illinois at Urbana–Champaign Foellinger Auditorium; and also at a side chamber of the Palace of Charles V, in the
Alhambra.
More generally, in the gravitational
two-body problem, if the two bodies are bound to each other (that is, the total energy is negative), their orbits are
similar ellipses with the common
barycenter being one of the foci of each ellipse. The other focus of either ellipse has no known physical significance. The orbit of either body in the reference frame of the other is also an ellipse, with the other body at the same focus.
Keplerian elliptical orbits are the result of any radially directed attraction force whose strength is inversely proportional to the square of the distance. Thus, in principle, the motion of two oppositely charged particles in empty space would also be an ellipse. (However, this conclusion ignores losses due to
electromagnetic radiation and
quantum effects, which become significant when the particles are moving at high speed.)
For
elliptical orbits, useful relations involving the eccentricity $e$ are:
The general solution for a
harmonic oscillator in two or more
dimensions is also an ellipse. Such is the case, for instance, of a long pendulum that is free to move in two dimensions; of a mass attached to a fixed point by a perfectly elastic
spring; or of any object that moves under influence of an attractive force that is directly proportional to its distance from a fixed attractor. Unlike Keplerian orbits, however, these "harmonic orbits" have the center of attraction at the geometric center of the ellipse, and have fairly simple equations of motion.
Phase visualization
In
electronics, the relative phase of two sinusoidal signals can be compared by feeding them to the vertical and horizontal inputs of an
oscilloscope. If the
Lissajous figure display is an ellipse, rather than a straight line, the two signals are out of phase.
Elliptical gears
Two
non-circular gears with the same elliptical outline, each pivoting around one focus and positioned at the proper angle, turn smoothly while maintaining contact at all times. Alternatively, they can be connected by a
link chain or
timing belt, or in the case of a bicycle the main
chainring may be elliptical, or an
ovoid similar to an ellipse in form. Such elliptical gears may be used in mechanical equipment to produce variable
angular speed or
torque from a constant rotation of the driving axle, or in the case of a bicycle to allow a varying crank rotation speed with inversely varying
mechanical advantage.
Elliptical bicycle gears make it easier for the chain to slide off the cog when changing gears.^{
[21]}
An example gear application would be a device that winds thread onto a conical
bobbin on a
spinning machine. The bobbin would need to wind faster when the thread is near the apex than when it is near the base.^{
[22]}
In lamp-
pumped solid-state lasers, elliptical cylinder-shaped reflectors have been used to direct light from the pump lamp (coaxial with one ellipse focal axis) to the active medium rod (coaxial with the second focal axis).^{
[23]}
In laser-plasma produced
EUV light sources used in microchip
lithography, EUV light is generated by plasma positioned in the primary focus of an ellipsoid mirror and is collected in the secondary focus at the input of the lithography machine.^{
[24]}
Statistics and finance
In
statistics, a bivariate
random vector$(X,Y)$ is
jointly elliptically distributed if its iso-density contours—loci of equal values of the density function—are ellipses. The concept extends to an arbitrary number of elements of the random vector, in which case in general the iso-density contours are ellipsoids. A special case is the
multivariate normal distribution. The elliptical distributions are important in
finance because if rates of return on assets are jointly elliptically distributed then all portfolios can be characterized completely by their mean and variance—that is, any two portfolios with identical mean and variance of portfolio return have identical distributions of portfolio return.^{
[25]}^{
[26]}
Computer graphics
Drawing an ellipse as a
graphics primitive is common in standard display libraries, such as the MacIntosh
QuickDraw API, and
Direct2D on Windows.
Jack Bresenham at IBM is most famous for the invention of 2D drawing primitives, including line and circle drawing, using only fast integer operations such as addition and branch on carry bit. M. L. V. Pitteway extended Bresenham's algorithm for lines to conics in 1967.^{
[27]} Another efficient generalization to draw ellipses was invented in 1984 by Jerry Van Aken.^{
[28]}
In 1970 Danny Cohen presented at the "Computer Graphics 1970" conference in England a linear algorithm for drawing ellipses and circles. In 1971, L. B. Smith published similar algorithms for all conic sections and proved them to have good properties.^{
[29]} These algorithms need only a few multiplications and additions to calculate each vector.
It is beneficial to use a parametric formulation in computer graphics because the density of points is greatest where there is the most curvature. Thus, the change in slope between each successive point is small, reducing the apparent "jaggedness" of the approximation.
Drawing with Bézier paths
Composite Bézier curves may also be used to draw an ellipse to sufficient accuracy, since any ellipse may be construed as an
affine transformation of a circle. The spline methods used to draw a circle may be used to draw an ellipse, since the constituent
Bézier curves behave appropriately under such transformations.
Optimization theory
It is sometimes useful to find the minimum bounding ellipse on a set of points. The
ellipsoid method is quite useful for solving this problem.
^Apostol, Tom M.; Mnatsakanian, Mamikon A. (2012), New Horizons in Geometry, The Dolciani Mathematical Expositions #47, The Mathematical Association of America, p. 251,
ISBN978-0-88385-354-2
^The German term for this circle is Leitkreis which can be translated as "Director circle", but that term has a different meaning in the English literature (see
Director circle).